Manufacturing method of cigarette machine baking igniter

The cigarette machine baking igniter is mainly used for smoking to make fire, but also for kang things and other fire. Lighter wind resistance, moisture resistance is better than matches, even in bad weather can also be used. The shell of the lighter is mostly cuboid, but also has special shapes such as pen shape and trapezoid, and is made of copper, magnesium aluminum alloy, plastic and so on. The use of lighters is very extensive, but the current domestic lighters can not be brought into the aircraft. This is because there is gas in the lighter, so there is a safety hazard. Of course, there is also an igniter heated by an electronic heating wire, but it is easy to misoperate when carrying and inconvenient to use. Not only is it unsafe to malfunction,

05

2022

/

05

Introduction of ceramic heating element

Ceramic heating element has the advantages of corrosion resistance, high temperature resistance, long life, energy saving, uniform temperature, good thermal conductivity, fast thermal compensation, etc., and does not contain lead, cadmium, mercury, hexavalent chromium, polybrominated biphenyls, polybrominated diphenyl ethers and other harmful substances, in line with the EU RoHS and other environmental protection requirements.

24

2022

/

05

Basic knowledge about PTC ceramic heating element

The ceramic heating element is a high-energy heater with uniform heat distribution, and a metal alloy with excellent thermal conductivity to ensure uniform hot surface temperature and eliminate cold hot spots of the equipment. There are two types of ceramic heaters, namely PTC ceramic heaters and MCH ceramic heaters. The materials used in these two products are completely different, but the finished products are similar to ceramics, so they are collectively referred to as 'ceramic heating elements '.

31

2022

/

05

These consumer electronics are used on the MCH ceramic heater

MCH is the abbreviation of cermet heating element. It uses high-temperature co-fired multilayer ceramic technology to print heating resistance slurry on the tape casting body (zirconia, alumina ceramic or zirconia toughened alumina ceramic, etc.), and then multilayer, The heating circuit is built into the ceramic material and sintered at about 1650 degrees to make it integrated. The ceramic body plays a role of protection and insulation. The metal ceramic heating element has no open flame, corrosion resistance, high temperature resistance, long service life, high efficiency and energy saving, stable and uniform, and fast thermal compensation. The product does not contain lead, mercury, hexavalent chromium and other harmful substances, and can fully meet the EU environmental requirements.

30

2022

/

06

Heating expert: alumina ceramic heating body

Many household appliances in life need to rely on their heating components to heat, such as coffee machines, drinking fountains, ovens and so on. In the past, the components that bear the "big responsibility" of heating are often based on metal as the basic structural raw material. During use, due to long-term heat, the components are easily oxidized, which affects their service life. In order to avoid these problems, it is natural to look for alternative materials, alumina ceramic is a good choice. After printing resistance paste on alumina ceramic, high temperature co-firing synthesis, electrode and lead processing, a new generation of medium and low temperature heating element-alumina ceramic heating element can be produced.

15

2022

/

07

MCH is the abbreviation of metal ceramic heating body MCH is the abbreviation of metal ceramic heating body

MCH is the abbreviation of cermet heating element, namely cermet heating element. Using high-temperature co-combustion multilayer ceramic technology, according to the design requirements of the heating circuit, the heating resistance paste (high melting metal such as tungsten, molybdenum, manganese, silver, palladium, etc.) is printed on the flowing steel billet (zirconia, alumina ceramic or zirconia toughened alumina ceramic, etc.), and then a multi-layer superimposed heating wire is built in the ceramic material and sintered at about 1650 ℃. The ceramic body plays a role of protection and insulation. The heating body has no open flame, corrosion resistance, high temperature resistance, long service life, energy saving and high efficiency, stable and uniform, and fast thermal compensation. The product does not contain lead, mercury, hexavalent chromium and other harmful substances, completely

01

2022

/

08

< 1...131415...17 >
Guangzhou Shi Chao

The main products are silicon nitride electric heating components, igniters, glow plugs and various shapes of hot-pressed silicon nitride temperature, wear-resistant ceramic parts, etc. Welcome new and old customers contact to negotiate

Guangzhou Shi Chao

86-020-84866661

E-mail：chenmy99@hotmail.com

Address: Building B6, 26 Xiaolong Jianlong Street, Shiqi Town, Panyu District, Guangzhou City, Guangdong Province, China

EN | CN

Copyright©2024 Guangzhou Shi Chao special ceramics manufacturing co ltd

粤ICP备06066573号-2

Powered by www.300.cn | SEO Tags |Business License | Urban substation